cuts for felling a tree

The backcut must leave sufficient. Make the cut approximately 18-20 inches from the ground no higher than your hip at a right angle.

Safe Tree Felling Diagram Given 6 Hours To Chop Down Trees I Would Spend The First 4 Sharpening The Axe Abraha Tree Felling Emergency Prepping Emergency

Make an angled cut that begins above the flat cut and slants down at 45 degrees to make a triangular notch.

. There are three types of basic cut you will use to fell a tree. This V-shaped cut should reach the center of the tree and the tips of the top and bottom cut must meet in the middle. The amount of back lean that can be overcome is based on the height and diameter of the tree to be felled.

Cut to a depth of about a quarter of the trees diameter. Felling Small Trees Trees up to 8cm diameter can be cut straight through. Make A Back Cut.

Then release the tree from the back side with a cut below the bore cut. For your tree to have a smooth fall you will make a V-shaped notch on the side of the tree thats facing the direction where you want it to fall. Make a felling cut from the opposite side of the tree toward the notch.

The easiest choice is to fell the tree in the direction it would naturally fall due to slope overhang and wind direction. If your chainsaw has a felling sight on the housing use it as a guide. If you make the back cut to a point where it meets the tip of the first two cuts.

Clearing Branches Brush. Remove these from the area before you start to fell. Highlights of Manual Felling Techniques.

An undercut must be made in each tree being felled. Cut at about the knee height of a regular-sized person. Illustrates how to fell a tree using the Notch and Back-Cut technique.

The condition of the tree the terrain and local tradition mean that the type of directional notch may differ. Bore cut to establish a hinge and cut toward the back of the tree. Before you start cutting make sure to remove any branches or brush that may be in the way.

The conventional cut and the open-face cut. Felling in another direction requires a special technique more effort and is sometimes just impossible. It will also prevent the chain and guide bar from being trapped during the cut.

Make a Horizontal Cut This cut should not be higher than your hip and it should extend no more than one-third of the way into the tree. Decide the direction that you want the tree to fall because this is the side of. Additionally youll want to invest in personal protection equipment including gloves ear and eye protection.

Problems Trees heavily weighted in one direction Do not try to remove one or more limbs to balance the tree this is for professionals. Stop the cut leaving enough holding wood on the back side of the tree. Cut on a notch at a 70-degree angle.

Cut at about the knee height of a regular-sized person. Quick animated sequence to show the expected outcome of implementing the steps describ. The directional notch determines the direction of fall and you fell the tree with the felling cut.

Make a Wedge Cut The slice that is produced by this cut should look like a. Hinge wood of sufficient length and width is. A backcut must be made in each tree being felled.

Using a Chainsaw 1. As the back cut is sawn the wedges are driven in with an axe. Make a bore cut through the other.

You want to be sure to have a nice clean area as to make sure you are making cuts correctly. Use the chainsaw and make a clean horizontal cut at the base of the notch. This can be done with an ax or chainsaw and should be cut square to create a hinge for the tree as it falls.

You should be able to remove a wedge from the tree leaving a notch one-fifth of the way through the trunk. Then rotate the saw and make an upward 30-degree cut meeting the end of the first cut. An undercut must be made in each tree being felled.

Pointing the sight where you want the tree to fall will help you cut at the proper location on the tree. Make a flat cut one-fourth of the way through the tree trunk. As the video demonstrates when youre using a chainsaw to fell a tree its important to plan carefully.

Remove the notch of wood from the trunk if it does not come free immediately. Make a horizontal cut ⅓ through the tree. In this video Inbred Jed and myself demonstrate 8 different ways to drop a tree and the different applications of the different cutting techniqueswe go over.

A large tree may be felled against its natural lean by inserting one or more wedges in the back cut. You will need to execute a final cut. Keep in mind that the tree will fall perpendicularly to this horizontal cut.

With the tree on your left and your left shoulder against the tree make a 70-degree cut on the side facing the direction you want the tree to fall. Top Cut This is the first cut you will make and is the cut used to make the top of the notch. Undercut or Bottom Cut This is the second cut you will make and is used to cut the lower face of.

Felling a tree can be done using two methods. You can cut branches by making a downward cut at the base of the branches. With the tree on your left and your left shoulder against the tree make a 70-degree cut on the side facing the direction you want the tree to fall.

The cut should be made ¼ of the diameter of the tree or up to ⅓ of the diameter but no deeper. If youre cutting down a big tree you need to make use of wedges. This video walks you through both processes and helps you decide if felling the tree can be done properly or if it should be left to a professional.

The conventional cut and the open-face cut. The undercut must be of a size so the tree will not split and will. Make Your Back Cut.

First and foremost verify your Husqvarna saw has fresh oil along with a new or sharpened chain. Find Up To Four Tree Pros. To do this tilt the chainsaw and make a downward 60-degree angle cut stopping one-fifth of the way through the tree.

Trees up to 15cm diameter should be undercut on the front about a third of the way through before the felling cut is made from the back. This cut should be made about 3 inches above the bottom of the V-shaped cut. This is because the wedges will prevent the tree from falling in a wrong or dangerous direction.

Pin On Tree Trimming